We have the perfect solution for you.
I'd recommend going with two of the Buyers Products low profile LED floodlights, part # 3371492135. The lamp is pretty small, so if you have some room between the top of the rear door and the roof you could easily fit two of the 5-3/4 x 2-1/2 inch lamps in that space. If there's not enough room there you could mount the lamps on the sides of the trailer, up toward the top which would also work great for you.
Each lamp puts out about 1600 lumens, so... view full answer...
The Hollywood Racks Sport Rider SE2 Platform Bike Rack w/ Cargo Carrier # HR1450Z-85 that you referenced can be used in the trailer hitch of your truck but it's not rated for use at the rear of a camper like your Fun Finder as the ride quality there will be much rougher.
The closest bike rack solution we have then is the reinforced Swagman Dispatch part # S44FR which you'd use at the rear of the camper and then the A-frame platform # CC-255 would be a great choice to carry cargo above... view full answer...
That sounds like loose lug nuts. Which if you didn't retorque them after driving on them for a little bit they can work themselves loose. view full answer...
Yes, the MORryde Suspension Upgrade Kit for Tandem Axle Trailers part # MR76ZR will work with the Equa-Flex Cushioned Equalizers part # LC279687. I would however just retain the bushing already installed in the equalizer. The dimensions of the equalizer from the left and right bolt holes should be within about 1/4" of one another to remain compatible. view full answer...
The Classic Accessories PolyPro III Deluxe RV Cover # 052963732634 has zippered panels on the passenger side so that you can access the entry door whether it's towards the front, or in your case closer to the rear of the trailer. view full answer...
The etrailer # e68ZR is only available with the coupler lock in the silver finish, but you can get the locks separately as # e98895, # e98880 and # e98883 and choose the 'keyed alike' option. This would provide you with the same kit, but with a yellow slip-on coupler lock. view full answer...
We have exactly what you need to replace the electric brakes on your 2013 Cruiser RV Fun Finder X 214WSD travel trailer; the correct brakes along with the mounting hardware for them are the following parts:
- Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies # AKEBRK-35-SA
- Mounting Hardware for 10" Brake Assemblies # BRKH10B
Then to connect the wires all you need are the 5-pack Deka Heat Shrink Butt Connectors # DW05745-5. view full answer...
For your older Quest QX-3202 in your 2008 Cruiser RV Fun Finder X, I recommend checking out the:
-iRV RV Stereo # IRV64FR.
While this stereo is not the same size as your Quest CD player, measuring in at 8-1/4" wide x 4-3/8" tall x 7-1/8" deep this is the closest option available.
Additionally, this stereo features 1 HDMI, 1 5V charging port, 3 audio inputs, 1 video input, 2 video outputs (1 HDMI and 1 RCA), 1 antenna port, and when using the iRV app, you'll be able to use your phone... view full answer...
Yes, we carry the Valterra Deadbolt Lock for RVs # L32CS3108, which will give you a standard deadbolt lock like you would see in a house. This lock fits 1-3/8" to 1-3/4" thick RV doors.
If you're just looking for a entry door lock that comes with a deadbolt, like part # 295-000019, then I would first need to know the dimensions of your trailer's cutout hole. To get this you'll need to remove the current door lock and measure the hole's height and width. Once we have that number I can... view full answer...
Yes, we do have just what you need with the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR98RR. You will need to slightly adjust the brackets (pictured below) by unscrewing the bolts and sliding them inward to meet your 22-3/4" flange to flange measurement and then retightening the bolts.
As for the handrail, you'll want the Handrail for Second Generation 3-Step MORryde Steps # MR83AR.
I've attached some videos below that will walk you through installation... view full answer...
The Dexter 13-143 E-Z Flex equalizer had a 7-3/4 inch bolt hole to bolt hole dimension, you'd need the equivalent replacement with the same dimensions, part # K71-655-00 to retain your present suspension geometry. As you can see in the product reviews, the Dextere E-Z Flex is very highly rated by our customers. view full answer...